• One 64-bit dual-core Intel Itanium 2 processor; either 1.6-GHz/24 MB cache, or 1.6 GHz/18 MB cache, or 1.4 GHz/12 MB cache; or 1.6 GHz/24 MB 9150N processor, or 1.6 GHz/18 MB 9140N processor, or 1.4 GHz/12 MB 9120N processor
• One I/O backplane. Either PCI-X 2.0 backplane with 8 available slots or PCI-Express backplane with 8 available slots
• 2-GB PC2 4200 ECC×4 Single Rank Registered DDR2 SDRAMs (4×512MB DIMMs)
• 24 DIMM slots (1×24 DIMM slot memory carrier board)
• One hot swap power supply

• Four dual core 64 bit Intel Itanium 2 processors; either 1.6 GHz/24 MB cache, or 1.6 GHz/18 MB cache, or 1.4 GHz/12 MB cache; or 1.6 GHz/24 MB 9150N processor, or 1.6 GHz/18 MB 9140N processor, or 1.4 GHz/12 MB 9120N processor
• One I/O backplane. Either PCI-X 2.0 backplane with 8 available slots or PCI-Express backplane with 8 available slots
• 384 GB PC2 4200 ECC×4 Single Rank Registered DDR2 SDRAMs (24×8 GB DIMMs)
• 48 DIMM slots (2×24 DIMM slot memory carrier boards)
• Sixteen Serial Attached SCSI (SAS) disk drives
• Two hot swap power supplies (two supplies enables redundancy)

• Operating System support: HP UX 11i version 2 June 2006 Update, HP UX 11i v3, Linux RHEL AS 4 U4 and SLES 10, OpenVMS V8.3 or higher for Integrity Servers and Microsoft Windows Server 2008 for Itanium-based Systems, and Microsoft SQL Server 2005 and SQL Server 2008
• Choice of core storage card.
  For HP-UX and OpenVMS-based systems: Must select one of two choices: PCI-X 8 port Serial Attached SCSI (SAS) host bus adapter or PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller:
  1. The PCI-X 8-port Serial Attached SCSI (SAS) host bus adapter: Card will be installed in reserved core PCI-X I/O slot #1. This card supports up to two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays for HP UX and OpenVMS. The additional three drives (of the maximum of eight drives supported) can be accessed normally, but not configured for RAID. Factory set up of RAID 1 configurations is supported. When a second SAS Controller is required to support disks 9 through 16, it cannot be factory configured for RAID (unless it is done through Factory Express). For customer/field configured RAID arrays, the same limitations (two RAID 1 arrays and one global hotspare) exist. The additional three HDDs (14 through 16) can be accessed normally, but not configured for RAID. Please see rx6600 Ordering Guide for factory configuration details.
• NOTE: MirrorDisk/UX is available for SW Mirroring on all HDDs in HP UX based systems and HP Volume Shadowing (software Raid 1) for HDDs in OpenVMS-based systems.
  2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller: Requires PCI-Express Backplane (AD296A Option Code 300); card will be installed in public slot #3, leaving 3 available PCI-Express slots and 4 available PCI-X slots. This card supports internal RAID-1, 5 and 6 configurations. RAID-1 requires a minimum of two identical HDDs, RAID-5 requires a minimum of three identical HDDs, and RAID-6 requires a minimum of four identical HDDs. When a second core PCI-Express P400 RAID controller is required to support disks 9 through 16, it will be installed in slot #4, leaving two available PCI-Express slots and four available PCI-X slots. Second core controller cannot be factory configured for RAID (unless it is done through Factory Express). Please see rx6600 Ordering Guide for factory configuration details.
• NOTE: PCIe Generation 2 cards are NOT supported in slots 3 and 4 of the AD296A Option 300 PCIe I/O Backplane.
  For Windows and Linux based systems: Must select one of three choices: PCI-X 8 port Smart Array (P600) Serial Attached SCSI (SAS) controller, or PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller, or PCI-Express 16-port Smart Array (P800) Serial Attached SCSI Controller.
  1. PCI-X 8-port Smart Array (P600) Serial Attached SCSI (SAS) controller:
  Card will be installed in reserved core PCI-X I/O slot #1. Supports internal RAID 1, 5 and 6 configurations. RAID 1 requires two identical HDDs, RAID 5 requires three identical HDDs, and
  RAID 6 requires four identical HDDs. Factory set up of RAID 1, 5 and 6 configurations with Smart Array SAS controller is also supported. When a second SAS Controller is required to support disks 9 through 16, it cannot be factory configured for RAID (unless it is done through Factory Express) . For customer/field configured RAID arrays, all eight HDDs (9 through 16) can be configured for RAID levels 1, 5 and 6 in any combination. Please see rx6600 Ordering Guide for details.
  2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI (SAS) controller.
  Requires PCI-Express Backplane (AD296A Option Code 300); card will be installed in public slot #3, leaving 3 available PCI-Express slots and 4 available PCI-X slots. This card supports internal RAID-1, 5 and 6 configurations. RAID-1 requires a minimum of two identical HDDs, RAID-5 requires a minimum of three identical HDDs, and RAID-6 requires a minimum of four identical HDDs. When a second core PCI-Express P400 RAID controller is required to support disks 9 through 16, it will be installed in slot #4, leaving two available PCI-Express slots and four available PCI-X slots. Second core controller cannot be factory configured for RAID (unless it is done throughFactory Express). Please see rx6600 Ordering Guide for factory configuration details.
  3. PCI-Express 16-port Smart Array (P800) Serial Attached SCSI (SAS) controller:
  Requires PCI-Express Backplane (AD296A Option Code 200); card will be installed in public slot #3, leaving 3 available PCI-Express slots and 4 available PCI-X slots. This card supports internal and external RAID-1, 5 and 6 configurations. RAID-1 requires a minimum of two identical HDDs, RAID-5 requires a minimum of three identical HDDs, and RAID-6 requires a minimum of four identical HDDs. When a second core PCI-Express P800 RAID controller is required to support disks 9 through 16, it will be installed in slot #4, leaving two available PCI-Express slots and four available PCI-X slots. Second core controller cannot be factory configured for RAID (unless it is done through Factory Express). Please see rx6600 Ordering Guide for factory configuration details.
• NOTE: PCIe Generation 2 cards are NOT supported in slots 3 and 4 of the AD296A Option 300 PCIe I/O Backplane (Legacy).
• Core PCI-X dual port 10/100/1000Base TX LAN (with auto speed sensing; RJ 45 connector, Wake On LAN support)
• Integrated iLO2 Management Processor for remote management and HA monitoring
• Telnet and web console via 10/100Base TX management LAN (RJ 45 connector)
• Two RS 232 serial ports, one for console from the integrated management processor and one from the processor dependent hardware bus (PDH)
• Factory integration of processors, memory, disk drives, removable media, I/O cards, and HP Universal 10000 G2 series racks.
• Rackmountable into 19 inch cabinets-HP Universal 10000 G2 series as well as many third party racks, including field integration into existing HP System E racks
• Optional stand alone pedestal mount, field installation only.
• Three year warranty with next business day on site.

• N+1 Hot swap cooling
• One Hot swap power supply-optional second power supply for N+1 protection
• Hot Plug PCI X I/O slots (Note: Some I/O cards do not support hot plugging. Please see Supported I/O card Table 3 this chapter for details.)
• On line memory page deallocation
• ECC protected DDR2 memory
• Memory double chip spare to overcome single DRAM chip failures
• Dynamic Processor resilience and deallocation
• UPS power management
• Hot Plug internal disks
• Internal RAID support. See Standard Systems Features on previous page and rx6600 Ordering Guide for various levels of RAID support.
• Journal file system with HP UX
• Auto reboot
• HP Serviceguard for HP UX
• HP Serviceguard Extension for RAC for HP UX
• HP Serviceguard Extension for SAP for HP UX
• Serviceguard Manager for HP UX and Linux Clusters
• HP Event Monitoring Service
• HA Monitors for HP UX
• HA Toolkits for HP UX and Linux
• HP Mirrordisk/UX
• Extended Campus Cluster, HP Metrocluster, and HP Continentalclusters for HP UX
• HP OpenVMS clusters
• HP Volume Shadowing for OpenVMS
• HP RMS Journaling for OpenVMS
• HP System Insight Manager (SIM) for proactive fault management
• Microsoft Windows Server 2008 for Itanium-based Systems, and Microsoft SQL Server 2005 and SQL Server 2008
• HP StorageWorks Software for HP Integrity Servers running Windows Server 2003 Enterprise Edition. Includes Cluster Extension XP and EVA, Continuous Access, Business Copy and SQL Server Fast Recovery
• HP StorageWorks Cluster Extension XP for Linux

• Separate LAN for system management
• Password protection on console port
• Disablement of remote console ports
• SSL encryption on web console

• HP Ignite UX for installation and deployment of the operating system
• HP Software Distributor UX for software and patch management
• HP Integrity Essentials Foundation Pack for Linux
• HP Integrity Essentials Foundation Pack for Windows including Smart Setup CD for easy server setup and configuration

• Built in Integrity iLO 2 Management Processor for comprehensive remote server management of HP UX, Linux, Windows and OpenVMS
• HP Servicecontrol suite for HP UX servers including tools for system administration, asset management, and fault management
• HP UX kernel configuration for easy, dynamic kernel parameter changes
• HP System Insight Manager (SIM)

• Process Resource Manager for HP UX resource management
• HP UX Workload Manager for HP UX workload management based upon service level objectives
• HP OpenView GlancePlus Pack
• HP Intelligent Networking Pack for Windows
• HP Performance Management Pack for Windows
• Windows System Resource Manager (included with each copy of Windows Server 2003 Enterprise Edition)

Dual core Intel Itanium processors:

• 1.6 GHz with 24 MB Level 3 Cache, 12 MB per core processor (Upgrade Only)
• 1.6 GHz with 24 MB Level 3 Cache, 12 MB per core 9150N processor
• 1.6 GHz with 18 MB Level 3 Cache, 9 MB per core processor (Upgrade Only)
• 1.6 GHz with 18 MB Level 3 Cache, 9 MB per core 9140N processor
• 1.4 GHz with 12 MB Level 3 Cache, 6 MB per core processor (Upgrade Only)
• 1.4 GHz with 12 MB Level 3 Cache, 6 MB per core 9120N processor

All processors support:

• Level 2 Cache: 1 MB Instruction/256 KB Data per core
• Level 1 Cache: 32 KB
• Four threads (two threads per core)
• Single bit cache error correction
• 50 bit physical addressing
• 64 bit virtual addressing
• 4 GB maximum page size

• Processors can be installed one at a time
• Processors must be installed in the following sequence: 0, 1, 2, and 3
• Different speed and different cache size processors cannot be mixed in the same system

The HP Integrity rx6600 supports double data rate (DDR2) synchronous dynamic random access memory (SDRAM) DIMMs with ECC and double chip spare protection. The HP Integrity rx6600 can be ordered with one of the following two memory carrier boards:

• AD126A-Supports from 2 GB minimum to 96 GB maximum memory; 8.5 GB/s memory bandwidth. The AD126A can be replaced with the AD127A to increase maximum memory beyond 96-GB and to a maximum of 192-GB, or to increase memory bandwidth to 17.0 GB/s. Please note, there is no return credit for the AD126A.
• AD127A-Supports from 2 GB minimum to 384 GB maximum memory; 17.0 GB/s memory bandwidth.

• Memory must be installed in groups of four DIMMs, also known as quads
• Each quad must consist of equal density DIMMs
• Memory can be ordered in quads of 2 GB (4×512MB), 4 GB (4×1GB), 8 GB (4×2GB), 16 GB (4×4GB), or 32 GB (4x8GB)
• Minimum memory is 2 GB (4×512MB)
• Maximum memory is 384 GB, using twelve 16 GB memory quads in memory carrier option AD127A
• Memory must be loaded in the order depicted on the memory carrier board.
• Arrange DIMMs so that the quads with the largest capacity are in the lowest numbered slots.
• For best performance, all DIMM slots on both memory carrier boards should be populated with the same size DIMM.

The HP Integrity rx6600 can be installed in the field with the Field Rack Kit (AD053A with B01 feature code). This field kit contains the slide mounts, cable management arm, and all other hardware needed to mount an rx6600 into a 19 inch cabinet.

Refer to the 10000 G2 Series Rack Best Practices Guide for information on rack deployment, stabilization and transportation. Go to: http://www.hp.com/go/rackandpower for more information.

The rx6600 is also available in a stand-alone, pedestal form factor (AD308A). Kit will be shipped in a separate box for field installation only.

The HP Integrity rx6600 supports two I/O backplane options in order to provide maximum flexibility, I/O card availability, performance, scalability and reliability. The two options are a PCI-X 2.0 Backplane (AD296A Option Code 100) or a PCI-Express Backplane option (AD296A OptionCode 300). Only one backplane per system is supported.

PCI-X 2.0 Backplane:
This backplane provides ten PCI X I/O slots, two of which are reserved for Core I/O cards, and eight of which are available for I/O card expansion. The Core I/O slots will always be filled with either an HP PCI X 8 Internal Port Serial Attached SCSI (SAS) host bus adapter (for HP UX and OVMS systems) or an HP PCI X Smart Array (P600) 8 Internal Port Serial Attached SCSI (SAS) card (for Windows and Linux systems) (slot #1) and a PCI X dual port 10/100/1000Base TX LAN adapter (slot #2).

Each port of a Serial Attached SCSI card can be connected to a Serial Attached SCSI hard disk drive. When more than eight hard disk drives are required, a second HP PCI-X 8 port SAS card must be ordered. This second SAS card will be installed in the second core I/O slot, and the PCI-X dual port 10/100/1000Base TX LAN adapter will be moved out to a standard I/O slot. Note that when the LAN adapter is moved out to a standard I/O slot, Wake On LAN is not supported.

HP-UX and OpenVMS based systems with PCI-X 2.0 Backplane:
Must choose the HP PCI-X 8 Internal Port Serial Attached SCSI host bus adapter for Core I/O controller (AB036B Option Code 006 or Option Code 106). If factory configured RAID is not desired, select Option Code 006. If factory configured RAID-1 is desired, select Option Code 106. RAID-1 only is supported on the HP PCI-X 8 Internal Port SAS host bus adapter. When selecting Option Code 106, a minimum of 2 HDD's of the same size and speed are required. A maximum of two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays is supported. The additional three drives (of the maximum of eight drives supported on the controller) can be accessed normally, but not configured for RAID. When from 9 to 16 HDD's are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express). For customer/field configured RAID arrays, the same limitations (two RAID 1 arrays and one global hot spare) exist. The additional three HDDs (14 through 16) can be accessed normally, but not configured for RAID. Please see rx6600 Ordering Guide for factory configuration details. Please note that MirrorDisk/UX is available for SW Mirroring on all HDDs in HP-UX based systems and HP Volume Shadowing (software Raid 1) for HDDs in OpenVMS-based systems.

Windows and Linux based systems with PCI-X 2.0 Backplane:
Must choose the HP PCI-X 8 port Smart Array (P600) Serial Attached SCSI (SAS) controller for Core I/O controller (AB036B Option 100, or Option 500, or Option 510). Option 100 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 500 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 510 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. When from 9 to 16 HDDs are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express). Please see rx6600 Ordering Guide for details.

Remaining Eight (non-Core I/O) slots:
The two slots (#3 and #4) next to the Core I/O slots have their own dedicated 64 bit 266 MHz PCI X bus and their own independent 2.1 GB/s I/O channel. These slots should be used for high performance PCI X cards, such as clustering interconnects or multi port storage adapters. The next two slots (slots #5 and #6) each have their own dedicated 64 bit 133 MHz PCI X bus and their own independent 1.1 GB/s I/O channel. The independent buses and I/O channels provide improved performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput.

The remaining four slots (#7 through #10) share two 64 bit 66 MHz PCI X buses, with two slots allocated to each bus. Each pair of slots shares a 0.5 GB/s I/O channel.

NOTE: Hot plug operations are not supported with the Linux or OpenVMS operating systems or in the core I/O slots with any operating system.

All I/O slots are keyed for I/O cards with 3.3V signaling. Cards that use 5V signaling are not supported in the HP Integrity rx6600.

PCI-Express Backplane:
This backplane also provides ten I/O slots. There are two PCI X Core I/O slots; one PCI X Core I/O slot will always have a PCI X dual port 10/100/1000Base TX LAN adapter (slot #2), unless a second storage controller is required, in which case the second controller is configured in slot #2 and the LAN card is moved out to public slot #10, and one PCI X Core I/O slot is provided in the case that the HP PCI X 8 Internal Port Serial Attached SCSI (SAS) host bus adapter is chosen when ordering an HP UX or OpenVMS based system, or if an HP PCI X Smart Array (P600) 8 Internal Port Serial Attached SCSI (SAS) card is chosen (slot #1) when ordering a Windows or Linux based system. If a PCI Express 8 port Smart Array (P400, supports only internal connection to SAS disks) Serial Attached SCSI controller (supported with HP UX, OpenVMS, Windows, and Linux) is chosen, or if a PCI Express 16 port (8 internal ports and 8 external ports) Smart Array (P800) Serial Attached SCSI controller (for Windows and Linux only, also supports connection to external SAS disks) is chosen, the PCI X Core I/O slot remains empty and the PCI Express controller is installed in slot #3.

Each port of a Serial Attached SCSI card can be connected to a Serial Attached SCSI hard disk drive. When more than eight hard disk drives are required, a second 8 port Serial Attached SCSI card must be ordered. If a PCI-X card is chosen, it will be installed in the reserved PCI-X core I/O slot. If a PCI-Express card is chosen, it will be installed in slot #4.

HP-UX and OpenVMS based systems with PCI-Express Backplane:
These systems have the two choices for Core I/O controller; the HP PCI-X 8 Internal Port Serial Attached SCSI host bus adapter or the HP PCI-Express 8 Internal Port Smart Array (P400) Serial Attached SCSI controller.

1. HP PCI-X 8 Internal Port Serial Attached SCSI host bus adapter (AB036B Option Code 006 or Option Code 106). If factory configured RAID is not desired, select Option Code 006. If factory configured RAID-1 is desired, select Option Code 106. RAID-1 only is supported on the HP PCI-X 8 Internal Port SAS host bus adapter. When selecting Option Code 106, a minimum of 2 HDD's of the same size and speed are required. A maximum of two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays is supported. The additional three drives (of the maximum of eight drives supported on the controller) can be accessed normally, but not configured for RAID. When from 9 to 16 HDD's are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express). For customer/field configured RAID arrays, the same limitations (two RAID 1 arrays and one global hotspare) exist. The additional three HDDs (14 through 16) can be accessed normally, but not configured for RAID. Please see rx6600 Ordering Guide for factory configuration details. Please note that MirrorDisk/UX is available for SW Mirroring on all HDDs in HP-UX based systems and HP Volume Shadowing (software Raid 1) for HDDs in OpenVMS-based systems.
2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller (AB036B Option 130, or Option 530, or Option 540). Requires PCI-Express Backplane (AD296A Option 300). Option 130 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 530 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 540 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. When from 9 to 16 HDDs are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express). Please see rx6600 Ordering Guide for details.

NOTE: MirrorDisk/UX is available for SW Mirroring on all HDDs in HP UX based systems and HP Volume Shadowing (software Raid 1) for HDDs in OpenVMS-based systems.

Windows and Linux based systems with PCI-Express Backplane:
These system have three choices for Core I/O controller; the PCI-X 8 Internal Port Smart Array (P600) Serial Attached SCSI controller, or the PCI-Express 8 Internal Port Smart Array (P400) Serial Attached SCSI controller, or the PCI-Express 16-port (8 Internal/8 External) Smart Array (P800) Serial Attached SCSI controller.

1. HP PCI-X 8 port Smart Array (P600) Serial Attached SCSI controller (AB036B Option 100, or Option 500, or Option 510). Option 100 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 500 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 510 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. When from 9 to 16 HDDs are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express) . Please see rx6600 Ordering Guide for details.
   
2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller (AB036B Option 130, or Option 530, or Option 540). Requires PCI-Express Backplane (AD296A Option 300). Option 130 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 530 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 540 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. When from 9 to 16 HDDs are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express) . Please see rx6600 Ordering Guide for details.
   
3. PCI-Express 16-port Smart Array (P800) Serial Attached SCSI Controller (AB036B Option 150, or Option 550, or Option 560). Requires PCI-Express Backplane (AD296A Option 300). Option 150 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 550 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 560 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. When from 9 to 16 HDDs are ordered, a second SAS Controller is required to support disks 9 through 16. The second controller cannot be factory configured for RAID (unless it is done through Factory Express) . Please see rx6600 Ordering Guide for details.
   

Remaining Eight (non-Core I/O) slots:
The two slots (#3 and #4) next to the Core I/O slots share a PCI-Express x8 1.3-GB/s I/O channel. The next two slots (slots #5 and #6) each have their own PCI-Express x8 2.6-GB/s I/O channel. The independent I/O channels provide improved performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput. These slots should be used for high performance PCI X cards, such as clustering interconnects or multi port storage adapters.

The remaining four slots (#7 through #10) are PCI-X slots. Slots #7 and #8 each have their own dedicated 64 bit 133 MHz PCI-X channel; slot #7 is 1.1 GB/s and slot #8 is 0.5 GB/s. Slots #9 and #10 share a 64-bit 66-MHz PCI-X 0.5 GB/s I/O channel.

NOTE: Hot plug operations are not supported with the Linux or OpenVMS operating systems or in the PCI X Core I/O slots with any operating system. Hot plug operations are not supported for any operating system in slots #3 or #4.

All I/O slots are keyed for I/O cards with 3.3V signaling. Cards that use 5V signaling are not supported in the HP Integrity rx6600.

A7173A

The integrated multifunction I/O provides core I/O functionally and includes the integrated management processor, which provides remote management and high availability monitoring capabilities.

• PCI-X Dual port 10/100/1000Base T LAN with RJ 45 connector-Supports LAN boot for operating system installation.
• The base system offerings require choice of at least one HP 8 Port Serial Attached SCSI (SAS) controller. Choices vary depending on choice of I/O backplane (PCI-X 2.0 backplane or PCI-Express backplane) and choice of operating system. Please see Table 2.9.2 HP Integrity rx6600 Features - Standard System Features ealier in this chapter, or the section I/O Architecture beginning on page 2-230, and the rx6600 Ordering Guide.
• Factory configured RAID is available with all Core I/O controllers. Please see Table 2.9.2 HP Integrity rx6600 Features - Standard System Features ealier in this chapter, or the section I/O Architecture beginning on page 2-230, and the rx6600 Ordering Guide. When configuring for RAID, all HDD's in the system must be the same size and speed.

• Dedicated 10/100BaseTX LAN port for LAN console and embedded web console access.
• One RS 232 serial port for local console.
• Password protected console ports.
• Console mirroring between all local, modem, LAN, and web consoles.
• Remote power up and power down control.
• Configurable remote access control.
• Event notification to system console-Provides connectivity, information, and support for HP UX tools (such as STM and EMS) to notify by email, pager and/or HP response centers.
• Interface to system monitoring and diagnostic hardware via an internal IC bus.
• Secure Sockets Layer security on web console.
• Support for Integrated Lights Out version 2 (iLO v2) Advanced Pack activation key and license (AD301A). Firmware license installs on the integrated Management Processor Card. Integrated Lights Out (iLO) Advanced Pack provides additional remote management capabilities, including integrated remote console and virtual CD/DVD drive, and LDAP directory services, SSH security, and Group Actions with HP Systems Insight Manager (SIM).
• Basic graphic capabilities are available as an optional upgrade. The upgrade provides these capabilities via the Radeon 7000 2D graphics chip and 16 MB memory, which resides on the integrated Integrity iLO 2 management processor card. VGA port is provided on rear of the system. Supported resolutions and refresh rates include:

• SSL secured Web console accessible through the 10/100Base T management LAN
• Standard telnet connections accessible through the 10/100Base T management LAN
• Local VT100 or hpterm terminal, or VT100 or hpterm emulator via local RS 232 serial connection
• Remote VT100 or hpterm terminal, or VT100 or hpterm emulator via external modem
• VGA graphics console using the upgrade to the VGA port. This upgrade is required for Windows systems and optional for HP UX and Linux systems. Keyboard and mouse connections are provided by USB. OpenVMS doesn't support VGA console for boot operations, but supports the VGA device for graphics use after boot.
• Integrated Remote Console (virtual KVM) through the iLO 2 Advanced Pack (Windows systems only).

• The HP Integrity rx6600 supports up to sixteen internal Serial Attached SCSI (SAS) 2.5 inch hot plug disk drives.
• A PCI-X or PCI-Express 8 port host bus adapter provides 8 ports, 1 port per SAS disk, for point to point connection from the adapter to the disk. This means that each disk has its own 3 GB link. A second HP 8 Internal port host bus adapter must be ordered to support disks 9 through 16.
• Factory configured RAID is available with all Core I/O controllers. Please see Table 2.9.2 HP
• Integrity rx6600 Features - Standard System Features ealier in this chapter, or the section I/O Architecture beginning on page 2-230, and the rx6600 Ordering Guide. When configuring for RAID, all HDD's in the system must be the same size and speed.
• Cables required to connect the internal disk drives to the host bus adapter are shipped with the system; no need to order separately.
• 36-GB 10K and 15K, 72-GB 10K and 15K, and 146-GB Serial Attached SCSI (SAS) disks are supported. 300 GB 10K SAS disks will be supported on all operating systems in a future release.
• Optical media drives include a DVD ROM (AD142A) and DVD+RW (AD143A). A DVD drive is required for all OpenVMS, Linux, and Windows configurations. Third party software (not included with the AD143A) is required to support DVD write with Windows on AD143A. Please note that that the AD143A is not supported on HP UX based systems.

Using HP-UX TCS with EVFS:

Using HP-UX TCS to make the unattended boot capability of EVFS more secure is an important example of how HP-UX TCS can be integrated with other applications to enhance security. For more information see the "Protecting EVFS Keys with HP-UX TCS" chapter in the "HP-UX Trusted Computing Services Administrators Guide" available in the HP-UX Trusted Computing Services section at: http://docs.hp.com/en/internet.html

Please note that HP-UX 11iTCS requires:

(1) An HP zx2-based Integrity server (rx2660, rx3600, or rx6600) with a TPM installed, running HP-UX 11iv2 September 2006 release or later
(2) Installation of kernel patch PHKL_35428

To download TCS and EVFS, please see the HP-UX Software Depot web page at: http://software.hp.com

The HP Integrity rx6600 provides a high level of integrated power protection:

• N+1 redundant hot swap power supplies
• N+1 redundant AC power input protection with electrical phase isolation
• Power monitoring and control

The HP Integrity rx6600 supports a second hot swap power supply for N+1 protection. One supply is shipped as a standard part of every system and is required for correct operation. The hot swap design allows for the online replacement of a power supply when N+1=2 supplies are configured in the server.

The HP Integrity rx6600 provides an independent power input receptacle for each power supply. The independent design provides protection against losing the connection from a power cord or breaker. The HP Integrity rx6600 power cords should always be plugged into separate breakers when possible.