Optional drive cage bay

Optional drive cage bay

Announcing support for:

• HP 16GB 4Rx4 PC3-8500R-7 Kit

The next generation of the HP ProLiant ML370 (expandable tower chassis) and the new HP ProLiant DL370 (4U rack optimized chassis) deliver Industry-leading management tools, leading performance, expandability, flexibility and the latest energy efficient technologies. These servers are well-suited for deployment in growing businesses, remote office sites, or datacenters and have been designed to bring you (our customer) the utmost confidence to run your business.

Features included in both the HP ProLiant ML370 G6 and the HP ProLiant DL370 G6:

• Processors:
  • Up to two (2) Intel® Xeon® 5500 series processors series with Intel Turbo Boost technology which now allows customized adaptability for optimizing both power consumption and performance based on your respective requirements
  • Intel® 5520 chipset
• Memory:
• 18 DIMM slots
• Up to 192GB, using PC3-8500R DDR3 Registered (RDIMM) memory, operating at 800MHz when fully populated at 2 DIMMs per Channel in 12 slots
• Up to 24GB, using PC3-10600E DDR3 Unbuffered (UDIMM) memory, operating at 1066MHz when fully populated at 2 DIMMs per Channel in 12 slots
• Two DIMMs Per Channel at 1333MHz supported with ROM update via ROM Based Setup Utility (RBSU) for 1333MHz RDIMMs. UDIMM support is only on 12-slot servers.
• Storage Controller:
• Entry Models: HP Smart Array P410i/256 MB Controller (RAID 0/1/1+0/5/5+0)
  NOTE: Entry Models available for ML370 G6 models only.
• Base Models: HP Smart Array P410i/256 MB Controller (RAID 0/1/1+0/5/5+0)
• Performance Models: HP Smart Array P410i/512 MB BBWC Controller (RAID 0/1/1+0/5/5+0)
• Available upgrades: 256MB, 512MB with BBWC, Battery kit upgrade (for BBWC), and Smart Array Advanced Pack (SAAP)
• Internal Drive Support:
• Up to 24 small form factor (SFF) or 14 large form factor (LFF) hot-plug drive bays to support Serial-attached SCSI (SAS) and Serial ATA (SATA) drives
• Standard half-height DVD-ROM (all models)
• Two open half-height media bays available for tape drives, optical media, optional SAS HDD cage
• Network Controller:
• HP NC375i Integrated Quad Port Multifunction Gigabit Server Adapter
• Expansion Slots:
• Nine (9) available PCI-Express Gen2 expansion slots to provide you with the latest I/O performance (see "Standard Features -Expansion Slots" section below for more details); PCI-X (optional)
• Graphic Cards:
• Supports up to 3 x 300W Graphic Cards via Graphic Card Power Adapter kit
  NOTE: 2 PCIe Gen2 x16 (mechanical/electrical); 1 PCIe Gen2 x16 (mechanical) x8 (electrical)
• Ports:
• USB 2.0 support
• 6 total ports: (2) ports in front; (2) ports in rear; (1) port for internal key; (1) port for HP internal tape
• 1 internal Secure Digital (SD) slot
• Redundancy:
• Multiple layers of fault tolerance through critical component redundancy (power supply and fan redundancy), mirrored memory, embedded RAID capability, and full-featured remote Lights-Out management
• Power Sources:
• Dual Common Slot Bay for Right Sized, Hot plug and Redundant Power options
  • HP 1200W CS HE Silver Power Supply (optional)
  • HP 750W CS HE Gold Power Supply (standard on some models)
  • HP 460W CS HE Gold Power Supply (standard on some models)
• Infrastructure Management:
  
  • HP ProLiant Onboard Administrator (powered by the HP Integrated Lights-Out 2 management processor) for simplified server setup, health monitoring and recovery, power and thermal control, and lights-out remote administration.
  • HP Insight Control a product option, delivers essential infrastructure management that can help save time and money by making it easy to deploy, migrate, monitor, control and optimize your IT infrastructure through a single, simple management console. Insight Control supports both Windows and Linux-based central management servers.
  • HP Insight Dynamics for ProLiant, a product option, is an integrated command center that enables IT Staff personnel to continuously analyze and optimize a converged infrastructure, while automating and reducing the cost of common data center tasks by as much as 40 percent. This ultimately enables them to dynamically keep pace with the organization's changing business requirements.
    
• Form Factor:
• 4U Tower Chassis and 4U Rack Optimized Chassis
  • Redesigned 4U Tower Chassis and the new 4U Rack Optimized Chassis to better meet our customer's density requirements
• Operating Systems and Virtualization Software Support for ProLiant Servers:
• Supports Windows, RHEL, SLES, OEL, Solaris, VMware, and Citrix Essentials for XenServer
• Deployment/Serviceability:
• System Insight Display on the front bezel for quick and easy server diagnostics
• Quick Deploy Rail System includes sliding universal rails, an ambidextrous cable management arm and quick release levers for fast and easy serviceability
• Tool-less access to all system components for easy in rack serviceability
• Customer Self Repair (CSR): HP products are designed with many CSR parts to minimize repair time and allow for greater flexibility in performing defective parts replacement
• Warranty:
• This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners resellers. Hardware diagnostic support and repair is available for three years from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
  NOTE: Server Warranty includes 3-Year Parts, 3-Year Labor, 3-Year Onsite support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at: http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html

10

Integrated ATI RN50, 64 MB video standard

• 16 bit color: maximum resolution of 1600 x 1200
  
• 32 bit color: maximum resolution of 1280 x 1024
  

NOTE: Maximum resolution available via iLO 2 remote console is 1280 x 1024.

Managing the growing number of servers can be complex and expensive for your organization. IT managers need to address changing business needs with tools that meet the challenges of managing today's complex Datacenters.

HP provides management solutions that are designed to simplify a server's installation, configuration and maintenance throughout the entire server lifecyle. This provides the customer with higher levels of operational efficiency and highly reliable systems: www.hp.com/go/foundation.
The foundation pack includes:

• HP SmartStart
  
• HP Management
  
• HP ProLiant Firmware Maintenance

SmartStart version supported (minimum): SmartStart 8.20
http://www.hp.com/servers/smartstart

HP ProLiant Onboard Administrator (powered by the HP Integrated Lights-Out 2 management processor) simplifies server setup, health monitoring, power and thermal control, and lights-out remote administration of ProLiant ML, DL, and BL servers. HP ProLiant Onboard Administrator functions without additional software, and can be accessed from any location via a web browser. It works hand-in-hand with HP Systems Insight Manager, Insight Control suites, and the Insight Dynamics for ProLiant helping customers unlock the value of the ProLiant platform and deliver the highest possible quality of IT service to the business. See www.hp.com/go/ProLiantOA

HP Insight Control, a product option, delivers essential infrastructure management that can help save time and money by making it easy to deploy, migrate, monitor, remote control, and optimize your IT infrastructure through a single, simple management console.

Two versions of Insight Control are available, to serve environments requiring either a Linux-based or a Windows-based central management server: HP Insight Control for Linux, and HP Insight Control. See www.hp.com/go/insightcontrol

HP Insight Control includes one year of 24 x 7 HP Software Technical Support and Update Service ensuring rapid access to HP support staff and proactive delivery of software updates. For more information about this service, please visit: http://www.hp.com/services/insight.

Trusted Platform Module option kit

The TPM (Trusted Platform Module) is a microcontroller chip that can securely store artifacts used to authenticate the server platform. These artifacts can include passwords, certificates and encryption keys. Windows® BitLocker™ Drive Encryption (BitLocker) is a data protection feature available in Windows Server® 2008. BitLocker leverages the enhanced security capabilities of a Trusted Platform Module (TPM) version 1.2. The TPM works with BitLocker to help protect user data and to ensure that a server running Windows Server 2008 has not been tampered with while the system was offline. For more information about TPM, including a white paper, go to www.hp.com/go/TPM

NOTE: ProLiant OS pre-installed units will come with the partition required for TPM deployment.
NOTE: The TPM key is unique to every TPM deployed server and must be retained. Misplacing or losing the key could result in data loss.

It is highly recommended that you use the HP Power Advisor in defining the "Right-Size" power supply for your needs. HP offers four Power Supply Options:

• HP 460Watts, Common Slot, 92% Efficiency
• HP 750Watts, Common Slot, 92% Efficiency
• HP 1200Watts, Common Slot, 90% Efficiency

HP's ProLiant Common Slot Power supplies (460W & 750W) meet multiple Energy Efficiency Initiatives. Climate Savers Computing Initiative GOLD, ECOS Consulting 80PLUS GOLD and plans on offering models that meet the Energy Star for Server requirements when they are published.

HP's ProLiant Common Slot Power supplies (1200W) meet multiple Energy Efficiency Initiatives. Climate Savers Computing Initiative Bronze, ECOS Consulting 80PLUS Bronze Power Supply requirements.

Redundant Power: Optional (1+ 1 or n+n redundant) power supplies can be purchased through power supply option kits (see Redundant Options for part numbers).

Microsoft Windows Server
Microsoft Windows Server 2008 Hyper-V
Red Hat Enterprise Linux (RHEL)
SUSE Linux Enterprise Server (SLES)
Oracle Enterprise Linux (OEL)
Solaris
VMware
HP Citrix Essentials for XenServer

Rack 10000 G2 series Cabinets
The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-mounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to be fully loaded with servers using the latest processors.

CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment:

• Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation).
• Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 2.75 inches (7 cm).

CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.

NOTE: For additional information, refer to the Setup and Installation Guide or the Documentation CD provided with the server, or to the server documentation located in the Support section at the following URL: www.hp.com/servers/ml370-g6.

Quick deploy rail system provides tool-free support for racks with square or round mounting holes (including Compaq/HP 7000, 9000, 10000 G2 and HP series), with an adjustment range of 24" - 36". The ambidextrous cable management arm can be mounted on either the left or right side for improved cable management.

Support for all 2-post Telco racks requires the use of the standard rack kit and an additional option kit from Rack Solutions at: www.hp.com/go/rackandpower.

HP Factory Express offers configuration, customization, integration and deployment services for HP servers and storage products. Customers can choose how their factory solutions are built, tested, integrated, shipped and deployed.

Factory Express offers service packages for simple configuration, racking, installation, complex configuration and design services as well as individual factory services, such as image loading, asset tagging, and custom packaging. HP products supported through Factory Express include a wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network switches.

For more information on Factory Express services for your specific server model please contact your sales representative or go to: http://www.hp.com/go/factory-express.

HP Care Pack services provide total care and support expertise with committed response designed to meet your IT and business needs.

HP Care Pack services include coverage for the HP branded hardware options qualified for the server and purchased at the same time or afterward that are internal to the enclosure. This also includes the 22" and smaller external monitors and tower UPS options up to 3kVA. These items will be covered at the same service level and for the same coverage period as the server. Coverage of UPS Battery is not included, and standard warranty terms & conditions apply. For servers or storage systems installed within a rack, service also covers all HP qualified rack options installed within the same rack.

To fully capitalizing on your HP ProLiant servers' capabilities requires a service partner who thoroughly understands your server technology and systems environment. HP Services, an industry leader in provision of multi vender support solutions, provides a range of support services designed to meet the varying needs of your business. Whether an SMB, or large global corporation, HP has a ProLiant server support offer to help you speedily deploy and maximize system uptime.

Recommended Service - simplify ProLiant solution implementation, maintenance, and management.

• Support - 3-Year 4-Hour response 24x7 Same Business Day Coverage only
• Service - Installation and Start up only

Enhanced Service - optimize service level to increase IT performance and availability.

• Support - 3-Year Support Plus 24 only

Refer to the information on "Installation & Start-Up" for service on ProLiant server and Microsoft or Linux O/S per the Customer Description and/or Data Sheet; to be delivered on a scheduled basis 8am-5pm, M-F, excluding HP holidays.

NOTE: For a complete listing of service offerings and information visit:
http://www.hp.com/services/proliantservices
http://www.hp.com/go/proliant/carepack

Base Models

HP ProLiant DL370 G6 X5550 2.66GHz Quad Core SFF High Performance Rack Server
487790-001

HP ProLiant DL370 G6 X5550 2.66GHz Quad Core SFF Performance ICE Rack Server
576411-001

HP ProLiant ML370 G6 E5540 2.53GHz Quad Core SFF Base Tower Server
487791-001

(1) Intel® Xeon® Processor E5540 (2.53 GHz, 8MB L3 cache, 80W, DDR3-1066, HT, Turbo 1/1/2/2)

HP ProLiant ML370 G6 E5520 2.26GHz Quad Core SFF Entry Tower Server
487795-001

The ProLiant Smart Buy program offers a collection of promotional server and option products that are configured with SMB in mind, offered at discounted prices, and positioned for quick delivery. Smart Buy server offers are available for a limited time only.

HP NC375i Integrated Quad Port Multifunction Gigabit Server Adapter
Integrated Lights-Out embedded
HP Smart Array P410i/Zero Memory Controller
(8) Hot-Plug (SFF) SAS/SATA Drive Bays
(9) available PCI-e Gen2 slots
(5) USB ports
(3) Hot Plug Fans
Tower Form Factor

483874-B21

Optical Drives

HP Insight Control server deployment, Electronic License including 1 year of 24x7 Technical Support and Updates

462828-B21

NOTE: Memory configurations listed do not apply to "Factory Integrated Models".

For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator

Some DIMM installation guidelines are summarized below:

• For servers with eighteen (18) memory slots:
  
  • There are three (3) channels per processor; six (6) channels per server
    
  • There are three (3) DIMM slots for each memory channel; eighteen (18) total slots
    
  • Memory channel 1 consists of the three (3) DIMMs that are closest to the processor
    
  • Memory channel 3 consists of the three (3) DIMMs that are furthest from the processor
    
• DIMM slots that are white should be populated first
  
• Do not mix Unbuffered memory (UDIMMs) with Registered memory (RDIMMs)
  
• Do not install DIMMs if the corresponding processor is not installed
  
• If only one processor is installed in a 2CPU system, only half of the DIMM slots are available
  
• To maximize performance, balance the total memory capacity between all installed processors
  
• It is not required, but it is recommended to load the channels similarly if possible
  
• You can only have up to eight (8) ranks installed per channel
  
• You can only install two quad-rank DIMMs per channel
  
• You can only install two UDIMMs per channel; if available, the third slot in the channel must remain empty
  
• Populate DIMMs from heaviest load (quad-rank) to lightest load (single-rank) within a channel
  
• Heaviest load (DIMM with most ranks) within a channel goes furthest from the chipset
  
• For memory mirroring mode, channel 3 must be unpopulated. Channels 1 and 2 are populated identically
  
• For lock-step mode, channel 3 must be unpopulated. DIMMs in channels 1 and 2 will be installed in pairs. The paired slots will be 1,4; 2,5; 3;6 on a 3DPC system or 1,4; 2,5; on a 2DPC system
  
• No mixing DIMM voltage; all DIMMs must be the same voltage
  

DIMM slot and configuration diagrams
Basic memory slot & population diagram

• Population order; start with "A" first, "B" second, "C" third, etc.

Standard memory configuration (1 CPU model)

• 6GB, consisting of three (3) 2GB dual-rank PC3-10600 RDIMMs

Standard memory plus optional memory (1 CPU model)

• 54GB, consisting of three (3) 2GB RDIMMs plus six (6) 8GB RDIMMs
  • 3x 2GB dual-rank PC3-10600 RDIMMs
  • 6x 8GB dual-rank PC3-10600 or PC3-8500 RDIMMs

Standard memory replaced with optional memory (1 CPU model)
RDIMM maximum configuration

• 72GB, consisting of nine (9) 8GB dual-rank PC3-10600 or PC3-8500 RDIMMs

UDIMM maximum configuration (1 CPU model)

• 12GB, consisting of six (6) 2GB dual-rank PC3-10600 UDIMMs

Standard memory replaced with optional memory (2 CPU model)
RDIMM maximum configuration

• 192GB, consisting of twelve (12) 16GB Quad-Rank PC3-8500 RDIMMs

UDIMM maximum configuration (2 CPU model)

• 24GB, consisting of twelve (12) 2GB dual-rank PC3-10600 UDIMMs

External Storage

Rack Weight
(approximate)

To review typical system power ratings use the HP Power Advisor which is available via the online tool located at URL: www.hp.com/go/proliant-energy-efficient

- Click on the system of interest. Example: DL370 G6 or ML370 G6
- Follow the instructions of the next screens.

Smart Array P410i Controller

Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to: http://www.hp.com/go/green. To recycle your product, please go to: http://www.hp.com/go/green or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.

The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at: http://www.hp.com/go/green. These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.